Canrig 6027 Top Drive Parts & Model Identification

Identify a Canrig 6027 part by model suffix, serial number and drawing, with references from Canrig bulletins TDS-161 and 100.

Identify a Canrig 6027 replacement part by the exact model suffix, machine serial number and assembly drawing. This page brings together manufacturer bulletin references for the 6027 family so a parts enquiry can distinguish a documented component from an assumed substitute.

Request a Canrig 6027 parts quotation

Canrig 6027 model identification

Record What the manufacturer evidence establishes
Model family 6027 appears in Canrig product bulletins; preserve any additional suffix shown on your nameplate.
Capacity reference Bulletin 100 discusses a 275-ton top drive application. Use the installed machine’s certified ratings for engineering or lift planning.
Motor and cooling configuration Bulletin 100 discusses GE-761 DC and WEG AC motor cooling. Do not assume all 6027 equipment has the same motor or controls.
Specification gaps Power, torque, speed, installed weight, connections and dimensions require the equipment-specific datasheet. They are not inferred from the model number.

Lower main bearing references: Bulletin TDS-161

Canrig’s bulletin dated 12 July 2016 identifies the 6020, 6025 and 6027 families and warns against unapproved lower main bearings. Its documented references are:

Canrig reference Description OEM reference in the bulletin
M01-1002-010 Tapered roller bearing cone Timken HH949549
M01-1003-010 Tapered roller bearing cup Timken HH949510
M01-1062-010 Tapered roller bearing assembly FAG F-579072

The bulletin treats the cone and cup as a set and identifies the assembly as another documented option. These historical references are identification aids; they do not establish current stock, an unrestricted substitution or approval of an aftermarket equivalent. Confirm the current manufacturer instruction and installed configuration before ordering. Bearing inspection and replacement belong with qualified personnel using the applicable OEM procedure.

Air-pressure switch references: Bulletin 100

Canrig’s bulletin dated 20 March 2005 identifies N10161-3 as the revised switch reference replacing N10161 for its stated motor-cooling application. It lists specific machine serial numbers: 036, 049, 116, 123, 160, 166, 173, 189, 197 and 257.

A low-air alarm alone does not prove a switch is defective or establish which component is required. Include the motor nameplate, machine serial and existing switch reference. Do not bypass a protective circuit or apply a historical setting as a general adjustment instruction.

Other 6027 component enquiries

  • Washpipe and seals: send the installed assembly reference, pressure requirement and exact seal or packing position.
  • Valve or actuator parts: distinguish the complete valve from the actuator and its internal components.
  • Motor, blower and controls: include nameplates, voltage/frequency where relevant, component tags and drawing revision.
  • Hydraulic cylinders and pipe handling: identify the cylinder or assembly and the required individual item.

These are enquiry categories, not a complete verified 6027 bill of materials. Additional part numbers will be added only when supported by the correct manufacturer documentation.

Prepare a useful Canrig 6027 RFQ

Include the model suffix and serial, assembly drawing/revision, original part number, quantity, delivery destination and required documentation. State whether you need an individual component, a matched set, a service kit or a complete assembly. Ask the quotation to confirm the proposed manufacturer, condition, compatibility basis and delivery terms.

Enquire about a 6027 bearing, switch or assembly

Questions before ordering

Can a 6027 part be selected from a generic Canrig parts list?

Use that list as a starting point only. Check the model suffix, serial number, assembly revision and any later manufacturer bulletin before selecting a part.

Does a listed reference mean the part is available?

No. Availability, source, current supersession and documentation must be confirmed in the quotation.

How do I send drawings or photographs?

Use the enquiry form to describe the requirement. If drawings or photographs are needed, the sales team will reply to your email so you can send them.

Manufacturer sources

Sources checked 15 November 2026. Bulletin dates identify the original documents, not new product announcements.

Canrig equipment and parts overview · Top drive manufacturer and model directory · Top drive component guide