NOV TDS-11SA Specifications & Spare Parts

Document reference values for the NOV TDS-11SA and what to send for a replacement-part enquiry: serial number, drawing revision and installed options.

The TDS-11SA is an established NOV top drive design, not a newly introduced model. Its large installed base makes accurate configuration identification especially useful for replacement-part enquiries.

TDS-11SA published reference specifications

Parameter Published reference
Hoisting and rotating capacity 500 short tons
Motor arrangement 2 × 400 hp AC induction motors
Continuous torque 37,100 ft-lb at 110 rpm
Maximum speed 228 rpm
Working height 19 ft
Reference weight 28,000 lb
Gear ratio 10.5:1
Water course 3 in
Washpipe packing pressure 7,500 psi
Pipe handler PH-75
IBOP pressure rating 15,000 psi

These are document reference values, not confirmation of a particular machine’s configuration or fitness for service. Confirm the serial number, drawing revision and installed options before selection.

Base unit or upgraded system?

For a documented 1,200 hp conversion, see the TDS-11SAE upgrade specification and parts guide, including gearbox changes and conversion-record checks.

A machine marked TDS-11SA may have received an upgrade. Before ordering, establish whether the installed system retains the original 800 hp configuration or has a documented higher-power conversion. Motor ratings alone do not identify the full conversion scope. Gearbox, pipe-handler and electrical modifications must be checked against the installed records.

TDS-11SA component and spare-parts enquiry map

Component group Information needed to identify the part
Washpipe and packing Assembly reference, bore, pressure rating and installed seal arrangement
PH-75 pipe handler and link tilt Pipe-handler serial/reference, drawing revision, cylinder and torque-arrestor details
IBOP stack and actuator Upper/lower valve references, connections and actuator assembly number
Transmission and lubrication Gearbox assembly, installed upgrade status, bearing or seal item positions
Motors, blowers, VFD and service loops Motor nameplates, drive references, cable/connector drawings and cooling configuration

This is a component enquiry map, not a verified parts bill of materials. Exact part numbers and compatibility will be added only when supported by the correct manufacturer parts list or equipment records. Listing a component group does not confirm availability.

TDS-11SA spare parts: identify the assembly first

For a useful quotation, separate the top drive model from the installed assembly and the individual replacement component. A request for “TDS-11SA seal kit” can refer to different assemblies. Naming the washpipe, IBOP actuator, cylinder or gearbox helps narrow the requirement before a part reference is checked.

Enquiry Details that make it specific
Washpipe packing or sealing assembly Installed assembly reference, pressure requirement, bore and the existing packing or cartridge arrangement
IBOP valve versus actuator component State which item is required; include the valve or actuator identifier and the drawing position
PH-75 cylinder or pipe-handler item Pipe-handler assembly reference, cylinder/rod identifier and installed revision
Motor, blower or electrical component Nameplate, voltage/frequency where applicable, connector details and component tag
Gearbox bearing or seal Gearbox serial, drawing item and whether the machine has a documented upgrade

Request a TDS-11SA assembly-specific quote

Does a TDS-11S washpipe reference automatically apply to TDS-11SA?

No. NOV’s 5,000 psi Blak-JAK flyer groups TDS-9S, TDS-10S and TDS-11S under a 3-inch washpipe application and lists cartridge references 80506100 and 80506100S. Its note distinguishes the cartridge-only “S” reference from the package including tools. This is a limited manufacturer cross-reference, not proof that the same item fits every TDS-11SA installation.

The TDS-11SA model reference used in the specification table above lists 7,500 psi washpipe packing. Check the installed washpipe and assembly documentation before selecting a cartridge or packing set. We have deliberately not listed the 5,000 psi references as verified TDS-11SA parts.

Source: NOV 5,000 psi Blak-JAK application guide. Reviewed 14 November 2026. This application reference does not establish stock, supply origin or compatibility with a modified machine.

Common TDS-11SA parts-enquiry questions

Can I request a quote without a part number?

Yes. Send the equipment serial number, assembly drawing or photographs, and describe the component’s location. Identification must be completed before a proposed part is treated as a confirmed match.

Should I request a kit or the complete assembly?

State whether the request is for a service kit, an individual component or a complete assembly. Ask the quotation to list inclusions and exclusions; a kit name alone does not define its contents.

Will an upgraded TDS-11SA use the original parts?

Do not assume so. Provide the conversion records alongside the original equipment data. Keep TDS-11HD, TDS-11SH and TDS-11-1400 upgrade requirements separately identified.

Can drawings or photographs be attached?

Describe the requirement in the enquiry form. If drawings or photographs are needed, the sales team will reply to your email so you can send them.

Request model-specific parts

Send the equipment model and serial number, assembly drawing/revision, part number and item position, quantity, photographs and delivery destination. State the required condition, origin, inspection and documentation. The quotation should confirm source, scope, compatibility basis, lead time and any exceptions.

Request TDS-11SA equipment or spare parts

NOV manufacturer reference for this page. Reviewed 14 November 2026.

Manufacturer and model directory · NOV / Varco equipment overview